FAQ
Questions asked before choosing RigFX. For a unit that doesn't behave, see Troubleshooting.
What power does it need?
- 12 V DC, 0.3 A: very low power consumption (Power).
- It runs on a battery with a D-Tap to XLR 4-pin cable.
- PoE is not supported: the Ethernet port of RigFX does not take power. We can provide an optional cable that splits PoE Ethernet into Ethernet and XLR power at the right voltage.
Which software do I need to set it up?
- The RigFX web application, in a browser on your network: it configures the system, zeroes the encoders and takes the rig measurements (First connection).
- To set it up faster and more precisely, we recommend:
- CalibFX Lens for the lens files,
- CalibFX Lineup for the two transforms that finish the setup:
- CalibFX is not mandatory, but it saves time and improves precision.
- RigFX is fully integrated with the ClassX virtual studio.
How is RigFX synchronised?
- By a Tri-Level or Black Burst Genlock7 signal, on BNC.
- By LTC9 timecode, on BNC.
- If both timecode and genlock are plugged in, they must come from the same sync generator.
- The timecode input can also jam-sync the unit: plug the timecode in for about 10 seconds, RigFX takes its time, then unplug the cable. As long as RigFX stays genlocked, its timecode stays accurate.
See Genlock / Sync.
Which protocols are supported?
- Outputs: FreeD6 D1 and OpenTrackIO11, over UDP on Ethernet, to up to three destinations.
- Inputs: FreeD6, OpenTrackIO11, Canon CV, and per edition Cartoni, Filmotechnic, Kuper or OptiTrack (Source). OptiTrack: Motive 3.0 to 3.5, NatNet 4.0 to 4.5 (Supported versions).
- An embedded web application to configure and monitor the unit.
- Everything runs over Ethernet. Wi-Fi is not recommended, but a Wi-Fi router on the studio network works for the web app.
Which lenses work with RigFX?
- With a lens cable:
- broadcast servo lenses: Canon, Fujinon, Angénieux,
- follow-focus systems on cinema lenses: Preston and cmotion (ARRI),
- smart lenses with the /i1 protocol: Cooke, Zeiss, Fujinon (/i1 carries no distortion data).
- With RigFX external encoders on the zoom and focus rings: we can provide them.
- Over the network:
See Lens FIZ source.
Is the lens connection plug and play?
- Yes, with a lens cable.
- External encoders learn each ring's travel by being turned from end stop to end stop, so they don't work on rings that turn endlessly.
- With a FreeD6 output, the render engine needs a lens file for the lens, since FreeD carries only the encoders: CalibFX Lens makes it.
- CalibFX Lens makes lens files for ClassX and for RigFX: load one into ClassX, or into RigFX when it sends OpenTrackIO (Lens pipeline).
How long does the setup take?
- A Cartoni e-Jibo with an encoded head: about 30 minutes from the flight case to a mounted rig, with two operators.
- A lens calibration from scratch: about 1 hour.
- A PTZ with OpenTrackIO11, or a Canon CV camera, needs no lens calibration: the lens data comes with it.
- Measuring the rig and entering its dimensions: about 5 minutes, or even faster and more precise with CalibFX Lineup.
- With a lens already calibrated, or lens data from the camera, mounting the jib and measuring it make the system operational in about 45 minutes.
How precise and how accurate is the tracking?
-
- better than 0.1 mm in position,
- better than 0.001° in angle,
Precision is how repeatable a measurement is: the smallest step between two measurements, and how little it moves when the rig doesn't. It depends on the tracking system. With Cartoni encoders it is:
stable and repeatable, with no visible jitter.
-
Accuracy is how close the tracked camera is to the real one. It mainly depends on the care taken during setup: accurate zeroing, precise physical measurements.
- CalibFX Lineup helps a lot to get the best accuracy: it solves the rig's offsets from what the camera sees.