Skip to content

Cartoni presets

Load a preset in Settings → Rig → Presets: it builds the rig chain, already bound to the right channels (Rig presets). The other dimensions come from the manufacturers' drawings: measure the ones in bold on your rig and enter them on the node cards (Measuring your rig). Tripod + FR7 and Slider + FR7, offered on every firmware, are on the Standard presets page.

Cartoni e-Jibo with an e-Sensor head and a camera, as drawn by the RigFX 3D view

Before loading a Preset14, zero each encoder with Set 0 at its reference position (Cartoni source → Calibration workflow).

Tripod + e-Sensor

A camera on a tripod with a Cartoni e-Sensor fluid head. Tutorial: Tripod + e-Sensor.

Wiring: e-Sensor pan → Cartoni input 1, tilt → input 2.

Node What it is Set
Tripod Floor to the top of the tripod bowl Z = your tripod height (1)
Head pan/tilt The e-Sensor's tilt axis, 0.1324 m above its base Pan = Cartoni 1 (negated), tilt = Cartoni 2
Sensor offset Tilt axis to the Sensor plane16 Y and Z = your sensor offset (2)

Tripod + e-Sensor: what to measure

Tripod + e-Sensor: sensor offset

e-Jibo + e-Sensor

A camera on an e-Sensor head, on the arm tip of a Cartoni e-Jibo on a tripod. Tutorial: e-Jibo + e-Sensor.

Wiring: e-Jibo pan → Cartoni input 1, tilt → 2; e-Sensor pan → 3, tilt → 4.

Node What it is Set
Tripod Floor to the top of the tripod bowl Z = your tripod height (1)
Jib pan/tilt The jib axle, 0.244 m above the bowl Pan = Cartoni 1, tilt = Cartoni 2 (both negated)
Arm Axle to the arm-tip pin Y = your arm length (2)
Counter-tilt Keeps the head plate level, as the jib's parallel arm does Tilt = Cartoni 2
Head plate The bowl plate on the arm tip From Cartoni's drawing
Head pan/tilt The e-Sensor's tilt axis, 0.1324 m above its base Pan = Cartoni 3 (negated), tilt = Cartoni 4
Sensor offset Tilt axis to the Sensor plane16 Y and Z = your sensor offset (3)

e-Jibo + e-Sensor: what to measure

e-Jibo + e-Sensor: sensor offset

e-Jibo + FR7 underslung

A Sony FR7 hanging under the arm tip of a Cartoni e-Jibo on a tripod. Tutorial: e-Jibo + FR7 underslung.

Wiring: e-Jibo pan → Cartoni input 1, tilt → 2. The FR7 sends its pan, tilt and lens over OpenTrackIO, in its ceiling installation mode, with its own position offsets at zero.

Node What it is Set
Tripod Floor to the top of the tripod bowl Z = your tripod height (1)
Jib pan/tilt The jib axle, 0.244 m above the bowl Pan = Cartoni 1, tilt = Cartoni 2 (both negated)
Arm Axle to the arm-tip pin Y = your arm length (2)
Counter-tilt Keeps the head plate level, as the jib's parallel arm does Tilt = Cartoni 2
Head plate The FR7 plate on the arm tip From Cartoni's drawing
PTZ pivot Plate to the FR7's tilt axis, 0.26 m down From Sony's drawing
PTZ The FR7's own pan, tilt and position OpenTrackIO11 pose
Sensor offset Tilt axis to the Sensor plane16, 0.048 m back From Sony's drawing

e-Jibo + FR7 underslung: what to measure