Skip to content

Cartoni Tripod + e-Sensor head

A camera on a tripod with a Cartoni e-Sensor fluid head. RigFX reads the head's pan and tilt from its Cartoni encoders and sends the camera's pose, with its lens, to the render engine. The Tripod + e-Sensor rig Preset14 builds the chain: you measure two dimensions.

You need

  • RigFX Cartoni, with the Cartoni firmware
  • a tripod with a Cartoni e-Sensor head, and its encoder cable
  • a camera
  • a Genlock7 reference
  • for lens data: a lens with encoders or a servo

1. What to measure

The Preset14 takes the height of the e-Sensor's tilt axis from Cartoni's drawing. Measure only these on your rig (figures):

1. Tripod height, from the floor to the top of the tripod bowl, where the head sits.

2. Sensor offset, from the e-Sensor's tilt axis (the centre of the tilt drum, on the side of the head) to the camera's Sensor plane16: forward (Y) and up (Z). Camera bodies mark the sensor plane with a circle crossed by a line.

2. Cabling

Wiring: e-Sensor pan and tilt into Cartoni inputs 1 and 2, the lens into Lens, the *Genlock*^[7](../../../../pages/reference/glossary.md#term-7)^ into Ref, the network to the render engine

  • Plug the e-Sensor's pan and tilt encoder cable into the head, and its other end into the Cartoni encoder inputs 1 (pan) and 2 (tilt) of RigFX Cartoni.
  • Connect RigFX to the studio network (Network), and the Genlock to its Ref input (Genlock / Sync). A lens with encoders or a servo plugs into the lens panel (Lens FIZ source).

3. Sync

In the web app, Settings → Sync:

  • Sync mode: External.
  • Target framerate: the studio's frame rate.
  • The status under the timecode reads Locked, and the measured FPS matches the target.

4. Cartoni source: zero the head

On the rig:

  • Level the head (bubble level on the e-Sensor).
  • Point the camera where pan should read 0, a direction easy to find again, such as along the studio's main wall, and lock the head.

In Settings → Source → Cartoni:

  • Enable channels 1 and 2 only.
  • Click Set 0 on channels 1 and 2: each reads zero at this position.

Success

Unlock the head: it is calibrated.

5. Rig: load the preset

In Settings → Rig, click Presets and load Tripod + e-Sensor (Rig presets). It builds the chain, already bound to Cartoni channels 1 and 2 (the nodes and what each one sets).

Enter your two measurements on the Tripod card (Z) and the Sensor Offset card (Y and Z):

Tripod node card: Z, the tripod height Sensor Offset card: Y and Z, from the tilt axis to the sensor plane

The Head pan/tilt card is bound to the encoders: pan to cartoni/1 with Negate on (the blue −), tilt to cartoni/2.

Head pan/tilt node card, pan and tilt bound to the Cartoni encoders

The Studio offset17 is not part of the Preset14: leave it at 0 to track relative to the tripod, or set it to where the tripod stands.

The web app's 3D view now moves with the rig, as here:

Camera Rig page with the Tripod + e-Sensor rig, Maquette view

Check the directions

Pan and tilt the head: the 3D view must follow the same way. If an axis turns the wrong way, toggle Negate on that field of the Head pan/tilt card.

6. Lens

In Settings → Lens, mode FIZ Source + Lens File (Lens):

  • FIZ source: the lens input your lens is plugged into.
  • Lens file: none for a FreeD6 output, where the render engine applies its own lens calibration; a .mrxlens file for an OpenTrackIO11 output, where RigFX resolves the lens (Lens pipeline).

7. Output

In Settings → Output, on one destination:

  • Protocol: FreeD6 or OpenTrackIO11, the one your render engine reads.
  • IP and Port: the render engine's.
  • Enable it.

Perfect tracking with CalibFX Lineup

Point the camera at the CalibFX cube and let CalibFX Lineup solve the Studio offset, the tripod height and the sensor offset from what the camera sees. On an OpenTrackIO output, tick Chain transforms (Output → OpenTrackIO options).